Jump to content
Московский Ветеринарный Форум
Sign in to follow this  
David Harry

+1 888 597 3962 Netgear Router Customer Support Phone Number

Recommended Posts

D-Link DIR-605L Firmware & Manual Links

The D-Link DIR-605L Support page contains all the information about the DIR-605L router that D-Link offers, including software downloads, documents, support videos, and FAQs.

Since there are two hardware versions of the DIR-605L router, there are also two different user manuals. Once you've chosen the version (A or B),  you'll see a download link for the user manual. The default credentials and IP address mentioned above are the same for both versions of the DIR-605L, but other details between the two versions may differ.

Having two different hardware versions means you must be certain to download the right firmware too since both versions use different firmware. The most recent firmware releases are available here.

You can find the right hardware version for your DIR-605L on either the bottom or back of the router; look for the letter next to H/W Ver. on the product label.

 

Every version of the D-Link DIR-615 router has a default username of Admin and, like most D-Link routers, no default password.

The default IP address used to access the DIR-615 router is 192.168.0.1.

The D-Link DIR-615 default username and password (which, again, is blank) is the same for each hardware and firmware version of the router you might have or be running, whether it be A, B, E, T, etc.

D-Link Router Customer Care Support  Phone Number

Most D-Link routers don't need a password by default, and that's true for the DI-524 router, too. When logging in to your DI-524, just leave the password field blank.

However, there is a default username for the D-Link DI-524. When asked to enter the username, use admin.

192.168.0.1 is the default IP address for the D-Link DI-524. This is the address that networked computers connect to, as well as the IP address that's used as a URL to make changes to the DI-524 through a web browser.

There are four different hardware versions for the DI-524 router (A, C, D, and E), but each of them use the exact same default password and IP address (and don't need a username).

Help! The DI-524 Default Password Doesn't Work!

If the blank default password for your DI-524 router isn't working, it most likely means you've changed it since it was first installed (which is good). However, the bad thing about changing the password to anything other than a blank one is that it's easier to forget it.

If you've forgotten your DI-524 password, you can just reset the router to its factory default settings, which will restore the password to the blank default one, as well as restore the username to admin.

Restoring the router back to factory default settings will not only remove a custom username and password but also any other changes you've made, like the Wi-Fi password, custom DNS settings, etc. Make sure you record those settings somewhere or make a back up of all the settings (skip down past these instructions to see how to do that).

Here's how to reset the D-Link DI-524 router (it's the same for all four versions):

1.         Turn the router around so you can see the back of it where the antenna, network cable, and power cable is plugged in.

2.         Before doing anything else, make sure the power cable is firmly attached.

3.         With something small and sharp, like a paperclip or pin, hold down the button inside the Reset hole for 10 seconds.

The reset hole should be on the far right side of the router, next to the power cable.

4.         Wait 30 seconds for the DI-524 router to finish resetting, and then unplug the power cable for a few seconds.

5.         Once you've reattached the power cable, wait another 30 seconds or so for the router to fully boot back up.

 

For more information : https://www.quickhelps.co/phone-number/d-link/

Share this post


Link to post
Share on other sites

Join the conversation

You can post now and register later. If you have an account, sign in now to post with your account.

Guest
Reply to this topic...

×   Pasted as rich text.   Paste as plain text instead

  Only 75 emoji are allowed.

×   Your link has been automatically embedded.   Display as a link instead

×   Your previous content has been restored.   Clear editor

×   You cannot paste images directly. Upload or insert images from URL.

Loading...
Sign in to follow this  

×
×
  • Create New...